Abstract
Fullerene acceptors typically possess excellent electron-transporting properties and can work as guest components in ternary organic solar cells to enhance the charge extraction and efficiencies. However, conventional fullerene small molecules typically suffer from undesirable segregation and dimerization, thus limiting their applications in organic solar cells. Herein we report the use of a poly(fullerene-alt-xylene) acceptor (PFBO-C12) as guest component enables a significant efficiency increase from 16.9% for binary cells to 18.0% for ternary all-polymer solar cells. Ultrafast optic and optoelectronic studies unveil that PFBO-C12 can facilitate hole transfer and suppress charge recombination. Morphological investigations show that the ternary blends maintain a favorable morphology with high crystallinity and smaller domain size. Meanwhile, the introduction of PFBO-C12 reduces voltage loss and enables all-polymer solar cells with excellent light stability and mechanical durability in flexible devices. This work demonstrates that introducing polyfullerenes as guest components is an effective approach to achieving highly efficient ternary all-polymer solar cells with good stability and mechanical robustness.
Similar content being viewed by others
Introduction
Organic solar cells (OSCs) have attracted considerable attention from both academia and industry due to their portability, transparency, flexibility, and facile fabrication1,2,3,4. Owing to the extensive research efforts devoted to material development and device optimization5,6,7, the power conversion efficiencies (PCEs) of OSCs based on small-molecular acceptors (SMAs) have exceeded 19% recently8,9,10,11, demonstrating their great potential as one of the most promising emerging solar technologies. Despite that, the device stability issue still remains a critical factor that limits the commercialization of SMA OSCs. To this end, all-polymer solar cells (all-PSCs), which employ both polymeric donors and acceptors as light absorbers (Supplementary Fig. 1), have been attracting the OSC community’s attention due to their additional advantages of robust mechanical toughness, and excellent light/thermal stability for commercial applications12,13,14,15,16. With the development of Y-series SMAs17,18,19,20 and their derived polymerized-SMAs (Supplementary Fig. 2)21,22,23,24,25,26,27,28, the all-PSCs based on Y-series polymer acceptors have realized decent efficiencies of over 17%29,30,31,32,33,34.
To further improve the PCEs of all-PSCs, constructing a ternary cell by introducing a guest component into binary host systems has been proven an effective and facile approach29,35,36,37. Regarding guest components, currently, one type of the most widely used guest materials of ternary OSCs are fullerene molecules (e.g., Phenyl-C61-butyric acid methyl ester (PCBM))38,39, which exhibit excellent electron-withdrawing properties and can enhance carrier transporting of OSCs40. Thus far, there have been a few reports of using PCBM as the guest component for ternary all-PSCs to improve device efficiencies41,42. Despite the good electron-accepting property of PCBM, its intrinsic instability remains a non-ignorable factor impairing device stability43,44. For instance, it has been found that PCBM molecules tend to dimerize under light illuminance and the dimerization significantly reduces the charge-transporting capacity of PCBM45,46. Meanwhile, the PCBM molecules are prone to aggregate into large clusters that decrease film mechanical robustness. Unfortunately, few alternatives have been reported that exhibit both comparable electron-transporting properties and good stability to replace PCBM or its derivatives.
In this work, we propose a new strategy for developing highly efficient and stable all-PSCs by replacing conventional PCBM molecules with polyfullerene materials. A poly(fullerene-alt-xylene) acceptor, named PFBO-C12, was synthesized and introduced as the guest component in ternary all-PSCs. Ultrafast optic and optoelectronic characterizations reveal that PFBO-C12 can promote the hole transfer process and suppress charge recombination. In addition, morphological characterizations show that the ternary blend maintained high crystallinity for fast carrier transport and more suitable phase separation with a smaller domain size for charge dissociation. As a result, the poly(fullerene-alt-xylene)-based ternary all-PSCs achieve an impressive PCE of 18.0%, and the device stability of ternary all-PSC is significantly improved compared to the PCBM counterpart. Meanwhile, PFBO-C12-based flexible all-PSCs are found to exhibit excellent bending durability in flexible devices, which maintained 90% of initial efficiency after 1000-time bending cycles. Overall, our work demonstrates that PFBO-C12 can work as an effective guest component to achieve high-performance all-PSCs with good efficiencies, stability, and mechanical toughness.
Results
Materials and optoelectronic characterization
The chemical structures of PM6, PY-V-γ, PCBM, and PFBO-C12 are shown in Fig. 1a. The polymer acceptor PY-V-γ was synthesized according to our previous works30,47. PCBM is chosen as another guest component for comparison. The synthesis details of the PFBO-C12 poly(fullerene-alt-xylene) are provided in Supporting Information48,49. The molecular weight of PFBO-C12 was measured to be 8802 g mol−1 (Mn) and 18,947 g mol−1 (Mw) by high-temperature gel permeation chromatography (HT-GPC), it should be noted that the measurement inaccuracy still remains due to the structure difference between polyfullerene and polystyrene standard. Cyclic voltammetry (CV, Fig. 1b, Supplementary Fig. 3) was used to estimate the energy levels of the materials in this work. It shows that PFBO-C12 exhibits comparable energy levels to PCBM. The ultraviolet–visible (UV–Vis) absorption spectra of the four materials were depicted in Fig. 1c. The maximum absorption peak (λmax, film) of PFBO-C12 is located at 340 nm, together with a broader shoulder absorption peak at 650 nm. Similar to PCBM, PFBO-C12 forms a complementary absorption to PM6 and PY-V-γ. The absorption spectra of PM6:guest acceptor (10% weight ratio) films exhibit the 0–0 peak enhancement from PCBM to PFBO-C12 (Supplementary Fig. 4a), which suggests a proper addition of PFBO-C12 can further promote the aggregation of PM6. Regarding the majority polymer acceptor in films, introducing the fullerene/polyfullerene guest acceptors was found to strengthen the intensity of PY-V-γ at λmax, film (~830 nm), implying their comparable miscibility and co-crystallization tendency in films (Supplementary Fig. 4c). As a result, both ternary systems display total absorption enhancement from 300 to 800 nm relative to the binary combination (Fig. 1d). The PFBO-C12-based blend shows even stronger intensity from 300 to 500 nm, which is beneficial for photon harvesting and photocurrent generation.
Photovoltaic device performance
To investigate the effects of PFBO-C12 on photovoltaic performance, all-PSCs were fabricated using a conventional device architecture of glass/ITO/PEDOT:PSS/active layer/PNDIT-F3N/Ag by a sequential deposition method (see details in the “Methods” section). After blending with PM6, the current-density-versus-voltage (J–V) curves of the three optimized devices were plotted in Fig. 2a, and the corresponding photovoltaic parameters of three groups of all-PSCs are summarized in Table 1. By constructing a pseudo-bilayer architecture50,51,52, the PCEs of both ternary cells increase compared to the binary system (Fig. 2b). PM6:PY-V-γ:PFBO-C12 based all-PSCs achieved the highest PCE of 18.0% with a high VOC (or small voltage loss), enhanced JSC and FF relative to the other two material combinations, which is also the record PCE for all-PSCs reported before the submission of this work (Supplementary Table 1). Next, we carried out external quantum efficiency (EQE) measurements to study the changes in JSCs of the optimized devices (Fig. 2c). After introducing the PCBM/PFBO-C12 guest components, the EQE response enhances from 670 to 830 nm, which is attributed to the stronger conjugation absorption in this range of the ternary blends. Meanwhile, the EQE response of the PFBO-C12-based all-PSCs slightly increases from 460 to 680 nm relative to the other two systems, leading to the highest Jcal of 25.1 mA cm−2. Overall, the integrated JSCs calculated from the EQE spectra match well with the values attained from the J–V curves (Table 1) and are consistent with the trend observed in UV–Vis absorption spectra.
Charge dissociation, recombination, and transport
Time-resolved photoluminescence (TR-PL) characterizations were performed to study their exciton dissociation behaviors (Supplementary Fig. 5a). The pristine PY-V-γ exhibited a PL decay lifetime of 0.38 ns and decreased to 0.20 ns after mixing with PM6 as the binary blend. As for ternary blends, the PL quenching process becomes even faster as the guest components were introduced, indicating both PCBM (0.19 ns) and PFBO-C12 (0.16 ns) help exciton dissociation. The trend agrees well with exciton dissociation probability (P, Supplementary Fig. 5b) measurement results that the PFBO-C12-based ternary devices showed the highest P among the three types of all-PSCs53.
Transient photocurrent (TPC) and transient photovoltage (TPV) measurements were conducted to study the charge extraction and recombination processes. In addition to the TPV spectra obtained under one sun illumination (Supplementary Fig. 6a, b)54, we also performed TPV characterization under different VOC levels via tuning the intensity of background light illumination to better discern their differences in charge recombination (Supplementary Fig. 6c, d). The photogenerated carrier density is calculated via TPC measurements under corresponding conditions. The TPV decay time τ under different VOC follows the power law with the calculated carrier density n (equation (1): τ = τ0(n/n0)−λ, and (λ + 1) represents the charge carrier recombination order)55,56. The carrier dependence of the TPV decay time of the three systems is shown in Fig. 2d. The fitted exponent λ are 1.73, 1.70, and 1.52 for the binary, PCBM and PFBO-C12-based all-PSCs, respectively. The binary system is found to have a higher recombination order (λ + 1), which indicates its more severe trap-assisted recombination. The less dependence on the decay time of the ternary systems suggests dominant bimolecular recombination for charge carriers and the trap-assisted recombination is greatly reduced in the PFBO-C12 ternary system. These results are further supported by light-intensity-dependent JSC and VOC characterizations of the three types of all-PSCs (Supplementary Fig. 6e, f), which show that PM6:PY-V-γ:PFBO-C12-based device exhibited suppressed bimolecular and trap-assisted charge recombination respectively, thus contributing to a higher FF.
The hole (μh) and electron (μe) mobilities of the three all-polymer blends were characterized via the space-charge-limit current (SCLC) method (Supplementary Fig. 7)57. As shown in Fig. 2e, f and Supplementary Table 2, the μh/μe of PM6:PY-V-γ were measured to be 8.6 × 10–4/9.0 × 10–4 cm2 V–1 s–1, which increased to 9.1 × 10–4/1.1 × 10–3 cm2 V–1 s–1 for PM6:PY-V-γ:PCBM blend. In comparison, PM6:PY-V-γ:PFBO-C12 exhibits the highest μe of 1.2 × 10–3 cm2 V–1 s–1 and a superior μh of 1.1 × 10–3 cm2 V–1 s–1 among three groups of devices. Moreover, PFBO-C12-based blends show a more balanced μh/μe value, which reduces charge accumulation and enables efficient charge extraction for high FFs58.
Morphology characterization and energy loss analysis
Grazing incidence wide-angle X-ray scattering (GIWAXS) characterizations can disclose the morphology characteristics of the films, and enable us to study the effects of the fullerene/poly(fullerene-alt-xylene) guests on film crystallinity and orientations59. As shown in Fig. 3a, b and Supplementary Table 3, all three blends exhibit similar π–π (010) stacking peaks located at ≈1.7 Å–1 in the out-of-plane direction, together with comparable coherent lengths (CLs) of 27 nm (dominated by PM6, Supplementary Fig. 8). In the in-plane direction, they also exhibit strong lamellar (100) peaks at qz ≈ 0.30 Å−1, implying the face-on orientation is also dominant in the blends that facilitate charge transport in the vertical direction. Meanwhile, both (100) and (200) peaks of the PFBO-C12-based blend show longer CLs relative to the other two combinations, indicative of a higher crystallinity for faster charge transport enabled by PFBO-C12. Grazing-incidence small-angle X-ray scattering (GISAXS) experiments were also involved to evaluate the impacts of guest components on the phase segregation of the blends60. Figure 3c, d shows the GISAXS results of the three all-PSCs, where the crystalline domain size (2Rg) of the ternary blends became smaller as the fullerene/poly(fullerene-alt-xylene) guest added, beneficial for charge dissociation as discussed above. Besides, the intermixing domain spacings (χ) decreased from 43.0 for the binary film, to 38.1 and 35.9 nm for PCBM- and PFBO-C12-based ternary blends. The higher domain purity of PFBO-C12-based blends will enable more effective charge extraction and suppress the charge recombination, which could be the major reason for their superior FFs and PCEs.
Furthermore, we looked into the energy loss (Eloss) among the three all-PSCs by carrying out in-depth photophysical experiments (Supplementary Fig. 9, Supplementary Table 4)61. A small energy offset between donors and acceptors can effectively suppress the charge-transfer (CT) state recombination through the hybridization of the local excited (LE) state and the CT state, resulting in reduced non-radiative recombination loss62. Due to the higher occupied orbitals of the guest components, the energy level offsets decrease between PM6 and the acceptors when the guest component is mixed with the PY-V-γ. Therefore, both ternary devices exhibit smaller ΔE3 relative to the binary devices. The final Elosss were determined to be 0.528, 0.521, and 0.514 eV for PM6:PY-V-γ, PM6:PY-V-γ:PCBM, and PM6:PY-V-γ:PFBO-C12 cells, respectively. The smallest Eloss of the PFBO-C12-based device should mainly result from the higher degree of conformational order of the polymer acceptor, with denser packing, fewer vibration states, and suppressed non-radiative recombination as above.
Exciton and charge dynamics study
Charge transfer processes in the blend films were investigated via transient absorption spectra (TAS) measurement. First, three blend films were excited at 800 nm, and the immediate rise of the ground-state bleach (GSB) signal (820–840 nm) corresponds to the absorption of PY-V-γ (Fig. 4a–c). The photoinduced absorption (PA) assigned to PY-V-γ at ~910 nm also emerges immediately after pump excitation. After 10 ps, a new PA band at ~960 nm emerges and starts to grow while the PA of PY-V-γ decays. Since PY-V-γ is selectively excited, the rise of PM6 GSB at ~640 nm can only result from the hole transfer from the acceptor to PM6, thus allowing us to probe the hole transfer process by monitoring the GSB of PM6. As shown in Fig. 4g, the hole transfer process in ternary blends is much faster than that in the binary. A bi-exponential model was introduced to fit the rise of donor GSB63. The rise lifetime τ1/τ2 are 1.48/21.37, 1.28/11.71, and 0.79/9.06 ps for the PM6:PY-V-γ, PM6:PY-V-γ:PCBM, and PM6:PY-V-γ:PFBO-C12, respectively (τ1 can be attributed to the exciton dissociation time at donor/acceptor interface, while τ2 represents the exciton diffusion time to the interface). These results indicate both PCBM and PFBO-C12 facilitate the hole transfer from PY-V-γ to PM6, and PFBO-C12 works more effectively on that. Besides, it is also noteworthy that the lifetime of the donor GSB signal of the PFBO-C12-based blend is slower (~3 ns), which is longer than the other two blends (~2 ns), implying a suppressed bimolecular recombination process in the polyfullerene system.
Subsequently, we preferentially excite the fullerene absorption region at 370 nm (Fig. 4d–f), and we find a higher intensity of TA response for the ternary blend, which is due to the stronger absorption in the UV region. As shown in Fig. 4h, the donor GSB emerges within our measurement time resolution (~150 fs) in all the blends, while the ternary blends show a faster rise of the acceptor GSB. We believe this is due to the Förster resonance energy transfer (FRET) from the fullerenes to PY-V-γ. A similar trend is also observed in the steady-state PL measurements (Supplementary Fig. 4d) that PY-V-γ shows PL enhancement when blended with fullerene components64. For the binary blend, there is only FRET from donor to acceptor. This also agrees with that the two ternary blends show stronger acceptor GSB signals than that of the binary blend. In addition, we also observe a slower decay of the acceptor GSB signal for the binary blend after 10 ps (Fig. 4i). This timescale corresponds to the rise of donor GSB after the fast electron transfer process from donor to acceptor. Since hole transfer leads to the significant decrease of acceptor GSB signal (as suggested by 800 nm excitation TA), this slower decay also suggests the slower hole transfer of the binary blend.
Device stability and mechanical robustness
We also look into the effects of fullerene guest components on device stabilities. Light-soaking tests were first conducted to evaluate the long-term operational stability of the three groups of all-PSCs. As shown in Fig. 5a–c, the PFBO-C12-based device showed the best light stability with a T80 of 1000 h under continuous 1-sun illumination, while both binary and PCBM-based ternary devices suffered from fast decay in FFs following with shorter T80s of 500 and 800 h, respectively. This result demonstrates the stabilization effect of PFBO-C12 in ternary cells. Subsequently, the flexible all-PSCs were fabricated with a structure of polyethylene naphthalate (PEN)/ITO/PEDOT:PSS/active layer/PNDIT-F3N/Ag to further investigate mechanical stability in flexible devices. The PM6:PY-V-γ:PFBO-C12-based device achieved the highest PCE of 14.6% among three flexible devices (Supplementary Fig. 10a and Supplementary Table 5), which is also one of the best efficiencies for flexible all-PSCs32,65. As shown in Fig. 5e–h, the PFBO-C12-based flexible devices display no obvious fracture at a bending radius (r) of 1 mm, relative to the flat device, demonstrating its intrinsic toughness after PFBO-C12 was introduced. We further tested the bending durability of the three groups of all-PSC as shown in Fig. 5d. PM6:PY-V-γ:PFBO-C12-based all-PSC maintained over 90% of the initial PCE after 1000 bending cycles, outperforming the other two types of devices. Such a good mechanical performance is mainly attributed to the elasticity of the PFBO-C12 polymer that enables the flexible cells more robust to mechanical bending.
To estimate the universality of the poly(fullerene-alt-xylene) guest, we choose another state-of-the-art all-polymer material combination of PM6:PYF-T-o as the host22, following the same procedure in device fabrication. It was found that both ternary devices showed enhanced FFs and PCEs, where the PM6:PYF-T-o:PFBO-C12-based devices realized the highest efficiency of 17.1% (Supplementary Fig. 10b, c and Supplementary Table 6). These results demonstrate the universality of polyfullerene guests in increasing PCEs of all-PSCs.
Discussion
In this work, we successfully introduce a poly(fullerene-alt-xylene) acceptor (PFBO-C12) as the guest component for high-performance all-PSCs. TAS characterization unveils that PFBO-C12 facilitates the hole transfer from PY-V-γ to PM6 and undergoes FRET with PY-V-γ. TPV/TPC results show that PFBO-C12 suppresses the charge recombination in the all-PSCs. Morphological investigations reveal that the incorporation of PFBO-C12 enhances the film crystallinity and reduces phase segregation simultaneously. Owing to these beneficial effects, the introduction of PFBO-C12 as the guest component to the PM6:PY-V-γ host blend eventually realizes high PCEs of 18.0% and 14.6% in rigid and flexible all-PSCs, respectively. Meanwhile, PFBO-C12-based ternary all-PSCs achieve both better light stability and bending durability compared to their PCBM counterparts. In conclusion, our work demonstrates that employing polyfullerene-type materials as guest components is an effective strategy for high-performance all-PSCs with better efficiencies, robustness, and stability.
Methods
Material synthesis and characterizations
PY-V-γ was synthesized according to our previous work. PM6 was purchased from Solarmer Energy Inc. Toluene was freshly distilled from sodium prior to use and benzophenone was used as the indicator. All other reagents and chemicals were purchased from commercial sources and used without further purification1H and 13C NMR spectra were obtained with a Bruker AV-400 MHz NMR spectrometer. Chemical shifts were reported in parts per million (ppm, δ)1 H, and 13C NMR spectra were referenced to tetramethylsilane (0 ppm) in CDCl3. Mass spectra were collected on a MALDI Micro MX mass spectrometer, or an API QSTAR XL System.
Molecular weight measurement
The molecular weight of PFBO-C12 was measured using a high-temperature gel permeation chromatography (HT-GPC, Agilent PL-GPC220) at 150 °C with 1,2,4-trichlorobenzene as the eluent and polystyrenes as the standard.
Optical characterizations
Film UV–Vis absorption spectra were acquired on a Perkin Elmer Lambda 20 UV/VIS Spectrophotometer. All film samples were spin-cast on ITO substrates.
Electrochemical characterizations
Cyclic voltammetry was carried out on a CHI610E electrochemical workstation with the three electrodes configuration, using Ag/AgCl as the reference electrode, a Pt plate as the counter electrode, and a glassy carbon as the working electrode. 0.1 mol L−1 tetrabutylammonium hexafluorophosphate in anhydrous acetonitrile was used as the supporting electrolyte. The polymer and small molecules were drop-cast onto the glassy carbon electrode from chloroform solutions (5 mg/mL) to form thin films. Potentials were referenced to the ferrocenium/ferrocene couple by using ferrocene as external standards in acetonitrile solutions. The scan rate is 100 mV s−1. The conversion of reduction/oxidation onsets and LUMO/HOMO energy levels can be described as: equation (2): ELUMO = −[e(E red–E Fc/Fc+)+4.8]; equation (3): EHOMO = −[e(E ox–E Fc/Fc+)+4.8].
Solar cell fabrication and testing
OSCs were made followed a device structure of glass/ITO (indium tin oxide)/PEDOT:PSS(poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate))/PM6:acceptor/PNDIT-F3N ([(9,9-bis(3’-(N,N-dimethylamino)propyl)−2,7-fluorene)-alt-5,5’-bis(2,2’-thiophene)−2,6-naphthalene-1,4,5,8-tetracaboxylic-N,N’-di(2-ethylhexyl)imide])/Ag. The patterned ITO-coated glass substrates were cleaned in detergent, de-ionized water, acetone, and isopropanol sequentially by ultra-sonic bath for 30 min, respectively, and then dried in an oven at 70 °C overnight. Further UV-Ozone treatment for 20 min was applied before use to improve its wettability. Then the PEDOT:PSS (Heraeus Clevios P VP. AI 4083, filtered at 0.45 μm) was spin-coated onto the cleaned ITO-coated glass substrate at 5200 rpm for 30 s followed by annealing at 150 °C for 15 min in the air to obtain ~30 nm thick film. The PEDOT:PSS-coated ITO substrates were then transferred into an N2-filled glove box for further device fabrication. PM6 was dissolved in chlorobenzene (CB, the concentration of donor was 9 mg mL−1) and stirred at 60 °C for 5 h to form a donor solution. The acceptor materials were dissolved in chloroform (CF, the concentration of acceptor was 9 mg mL−1) with the solvent additive of CN (1.5% of volume) with/without PCBM and PFBO-C12 followed by stirring at room temperature (RT) for 1 h to form the acceptor solution. The amount of PFBO-C12 was screened and the optimized ratio of PFBO-C12 is 10% (Table S7). For sequential deposition (SD)-based devices, PM6 solution was spun followed by the solution of the acceptor, and then the active layer was annealed at 100 °C for 5 min via SD processing. The active layer thickness is ~120 nm measured by the Bruker Dektak XT profilometer. A thin layer of PNDIT-F3N (~10 nm) was spin-coated onto the active layer, and Ag electrode (~100 nm) was deposited on top of the electron transfer layer in a thermal evaporator under a vacuum of 1 × 10−5 Pa through a shadow mask. The effective device area was 4.0 mm2 defined by a metal mask with an aperture aligned with the device area. The current–voltage (J–V) characteristics of the photovoltaic devices were measured by a Keithley 2400 Source Meter under RT in the glove box. The photocurrent was measured under AM 1.5 G illumination at 100 mW cm−2 using a standard Si solar cell (with KG5 filter) and a readout meter to calibrate the light intensity.
EQE measurements
EQE spectra were measured using an Enlitech QE-S EQE system equipped with a standard Si diode. Monochromatic light was generated from a Newport 300 W lamp source.
TR-PL characterizations
TR-PL measurements were carried out on encapsulated thin films. A 100 fs Ti:Sapphire oscillator (Coherent Mira 900) operating at 76 MHz repetition rate was tuned to 750 nm and focused to excite the sample. The PL was collected and guided into a spectrometer equipped with a silicon single-photon counter to carry out time-correlated single-photon counting (TCSPC), integrating the majority of the PL. Low-temperature measurements were carried out with the sample mounted inside a helium flow cryostat with an active feedback temperature controller. The PL spectra were obtained using a Si photodiode array detector.
Exciton dissociation probability analysis
Exciton dissociation (Pdiss) and collection (Pcoll) efficiencies can be calculated from the relationships between photocurrent (Jph) and effective voltage (Veff). Jph is defined as the difference between the dark current density (JD) and the current density under illumination (JL). The definition of Veff is the absolute value of V0−Vappl, where V0 refers to the voltage value when JL = JD and Vappl is the applied voltage. At high Veff, almost all excitons are separated and extracted, and Jph reaches saturation (Jsat). Accordingly, ηdiss and ηcoll can be determined by JSC/Jsat and Jmax/Jsat, respectively, in which Jmax is the current density at the maximal power output point.
TPV and TPC characterizations
The device samples were mounted on a conductive clip and under steady-state illumination from a focused Quartz Tungsten-Halogen Lamp light source. The measurements were performed with a background response similar to open-circuit voltage. An optical perturbation was applied to the devices with a 1 kHz femtosecond pulse laser under 600 nm excitation. The TPV signal was acquired by a digital oscilloscope at open-circuit conditions. TPC signal was measured under approximately short-circuit conditions with 50 Ω impedance. The intensity-dependent TPV and TPC measurements were performed by applying various neutral density filters to tune down the background white light and 750 nm pulse excitation. The TPV lifetime τ was fitted with the monoexponential model under a small perturbation approximation. The charges generated ΔQ by the pulse laser were calculated by the integrated TPC peak. The differential capacitance C is then calculated by equation (4): C = ΔQ/ΔV0, where the ΔV0 is the amplitude of the pulse-generated TPV signal at the corresponding experimental condition. C was fitted with exponential models as a function of VOC and then integrated with respect to voltage to acquire the carrier density. The TPV lifetime τ under different carrier densities n was then fitted to a power law with exponent λ55,56.
Hole mobility measurement
The hole mobilities were measured using the space charge limited current (SCLC) method, employing a device architecture of ITO/PEDOT:PSS/blend film/MoO3/Ag. The mobilities were obtained by taking current–voltage curves and fitting the results to a space charge limited form, where the SCLC is described by equation (5):
where ε0 is the permittivity of free space, εr is the relative permittivity of the material (assumed to be 3), μ is the hole mobility, L is the thickness of the film, Vappl is the applied voltage, Vbi is the built-in voltage (0.15 V) and Vs is the voltage drop from the substrate’s series resistance (Vs = IR, R was measured to be 10.8 Ω). From the plots of J1/2 vs. Vappl–Vbi–Vs, hole mobilities can be deduced.
Electron mobility measurement
The electron mobilities were measured using the SCLC method, employing a device architecture of ITO/ZnO/blend film/PNDIT-F3N/Ag. The mobilities were obtained by taking current-voltage curves and fitting the results to a space charge limited form, where the SCLC is described by equation (6):
where ε0 is the permittivity of free space, εr is the relative permittivity of the material (assumed to be 3), μ is the electron mobility, L is the thickness of the film, Vbi is the built-in voltage (0.15 V) and Vs is the voltage drop from the substrate’s series resistance (Vs = IR, R was measured to be 10.8 Ω). From the plots of J1/2 vs. Vappl–Vbi–Vs, electron mobilities can be deduced.
GIWAXS characterization
Grazing-incidence wide-angle X-ray scattering (GIWAXS) measurements were conducted at Advanced Light Source (ALS), Lawrence Berkeley National Laboratory, Berkeley, CA at beamline 7.3.3. Data were acquired at the critical angle (0.13°) of the film with a hard X-ray energy of 10 keV. X-ray irradiation time was 10 s, dependent on the saturation level of the detector. Samples were prepared on Si substrates using identical blend solutions as those used in devices. The coherence length was calculated using the Scherrer equation (7): CL = 2πK/Δq, where Δq is the full-width at half-maximum of the peak and K is a shape factor (1 was used here).
GISAXS characterization
The grazing incidence small-angel X-ray scattering (GISAXS) measurements were carried out with a Xeuss 2.0 SAXS/WAXS laboratory beamline using a Cu X-ray source (8.05 keV, 1.54 Å) and a Pilatus3R 300 K detector. The incident angle was 0.2°.
FTPS-EQE characterization
Fourier-transform photocurrent spectroscopy external quantum efficiency (FTPS-EQE) spectra were measured by using a Vertex 70 from Bruker optics and a QTH lamp. The electroluminescence signal was collected with a monochromator and detected with a Si-CCD detector.
TAS characterization
Two beams were split from the 800 nm output of a Ti:Sapphire laser amplifier (Coherent Legend Elite, repetition rate of 1 kHz, 100 fs). One of the split outputs was used to photoexcite the sample either directly at 800 nm or at other wavelengths generated in an optical parametric amplifier (Coherent OPerA Solo). The other split output was used to generate a white light continuum probe pulse by focusing the beam onto a sapphire plate. The optical pulses were spatially overlapped in the encapsulated thin-film sample and temporally delayed using a motor-driven delay stage. The probe was guided into a spectrometer (Acton instruments SpectraPro 275) with a 50 LP/mm grating and detected by a Si array detector. The pump-induced change in transmission (∆T/T) was recorded shot by shot. The experiment was performed with pump fluence of ~2 µJ cm−2 per pulse. Background signals were subtracted from the signal, and the chirp response was corrected. For the hole transfer study, a pump of 800 nm was used to selectively photoexcite the acceptor part. For the fullerene excitation, a pump of 370 nm was used to preferentially excite the guest components.
Reporting summary
Further information on research design is available in the Nature Portfolio Reporting Summary linked to this article.
Data availability
All data generated in this study are included in this published article and its Supplementary Information, and the raw data generated in this study are provided in the Source Data file. Source data are provided with this paper.
References
Zhang, G. et al. Nonfullerene acceptor molecules for bulk heterojunction organic solar cells. Chem. Rev. 118, 3447–3507 (2018).
Zhang, J. et al. Material insights and challenges for non-fullerene organic solar cells based on small molecular acceptors. Nat. Energy 3, 720–731 (2018).
Wadsworth, A. et al. Critical review of the molecular design progress in non-fullerene electron acceptors towards commercially viable organic solar cells. Chem. Soc. Rev. 48, 1596–1625 (2019).
Yan, C. et al. Non-fullerene acceptors for organic solar cells. Nat. Rev. Mater. 3, 18003 (2018).
Tong, Y. et al. Progress of the key materials for organic solar cells. Sci. Sin. Chim. 50, 437–446 (2020).
Yao, J. et al. Fluorinated perylene-diimides: cathode interlayers facilitating carrier collection for high-performance organic solar cells. Adv. Mater. 34, 2003690 (2022).
Liu, Y. et al. Recent progress in organic solar cells (Part II device engineering). Sci. China Chem. 65, 1457–1497 (2022).
Li, C. et al. Non-fullerene acceptors with branched side chains and improved molecular packing to exceed 18% efficiency in organic solar cells. Nat. Energy 6, 605–613 (2021).
Cui, Y. et al. Single-junction organic photovoltaic cell with 19% efficiency. Adv. Mater. 33, 2102420 (2021).
Zhu, L. et al. Single-junction organic solar cells with over 19% efficiency enabled by a refined double-fibril network morphology. Nat. Mater. 21, 656–663 (2022).
Chong, K. et al. Realizing 19.05% efficiency polymer solar cells by progressively improving charge extraction and suppressing charge recombination. Adv. Mater. 34, 2109516 (2022).
Wang, G. et al. All-polymer solar cells: recent progress, challenges, and prospects. Angew. Chem. Int. Ed. 58, 4129–4142 (2019).
Chen, S. et al. Highly flexible and efficient all-polymer solar cells with high-viscosity processing polymer additive toward potential of stretchable devices. Angew. Chem. Int. Ed. 57, 13277–13282 (2018).
Fan, B. et al. Surpassing the 10% efficiency milestone for 1-cm2 all-polymer solar cells. Nat. Commun. 10, 4100 (2019).
Wu, B. et al. All-polymer solar cells. J. Semicond. 42, 080301 (2021).
Zhang, Z.-G. et al. Constructing a strongly absorbing low-bandgap polymer acceptor for high-performance all-polymer solar cells. Angew. Chem. Int. Ed. 56, 13503–13507 (2017).
Yuan, J. et al. Single-junction organic solar cell with over 15% efficiency using fused-ring acceptor with electron-deficient core. Joule 3, 1140–1151 (2019).
Li, S. et al. New phase for organic solar cell research: emergence of Y-Series electron acceptors and their perspectives. ACS Energy Lett. 5, 1554–1567 (2020).
Yu, H. et al. Tailoring non-fullerene acceptors using selenium-incorporated heterocycles for organic solar cells with over 16% efficiency. J. Mater. Chem. A 8, 23756–23765 (2020).
Zhang, G. et al. Renewed prospects for organic photovoltaics. Chem. Rev. 2022, 14180–14274 (2022).
Luo, Z. et al. Precisely controlling the position of bromine on the end group enables well-regular polymer acceptors for all-polymer solar cells with efficiencies over 15%. Adv. Mater. 32, 2005942 (2020).
Yu, H. et al. Regio-regular polymer acceptors enabled by determined fluorination on end groups for all-polymer solar cells with 15.2% efficiency. Angew. Chem. Int. Ed. 60, 10137–10146 (2021).
Yu, H. et al. Fluorinated end group enables high-performance all-polymer solar cells with near-infrared absorption and enhanced device efficiency over 14%. Adv. Energy Mater. 11, 2003171 (2021).
Yu, H. et al. A difluoro-monobromo end group enables high-performance polymer acceptor and efficient all-polymer solar cells processable with green solvent under ambient condition. Adv. Funct. Mater. 31, 2100791 (2021).
Fu, H. et al. High efficiency (15.8%) all-polymer solar cells enabled by a regioregular narrow bandgap polymer acceptor. J. Am. Chem. Soc. 143, 2665–2670 (2021).
Du, J. et al. Polymerized small molecular acceptor based all-polymer solar cells with an efficiency of 16.16% via tuning polymer blend morphology by molecular design. Nat. Commun. 12, 5264 (2021).
Sun, H. et al. A narrow-bandgap n-type polymer with an acceptor–acceptor backbone enabling efficient all-polymer solar cells. Adv. Mater. 32, 2004183 (2020).
Jia, T. et al. 14.4% efficiency all-polymer solar cell with broad absorption and low energy loss enabled by a novel polymer acceptor. Nano Energy 72, 104718 (2020).
Sun, R. et al. Achieving over 17% efficiency of ternary all-polymer solar cells with two well-compatible polymer acceptors. Joule 5, 1548–1565 (2021).
Yu, H. et al. A vinylene-linker-based polymer scceptor featuring a coplanar and rigid molecular conformation enables high-performance all-polymer solar cells with over 17% efficiency. Adv. Mater. 34, 2200361 (2022).
Li, Y. et al. An efficient polymer acceptor via a random polymerization strategy enables all-polymer solar cells with efficiency exceeding 17%. Energy Environ. Sci. 15, 3854–3861 (2022).
Wang, J. et al. A new polymer donor enables binary all-polymer organic photovoltaic cells with 18% efficiency and excellent mechanical robustness. Adv. Mater. 34, 2205009 (2022).
Zhou, D. et al. Binary blend all-polymer solar cells with a record efficiency of 17.41% enabled by programmed fluorination both on donor and acceptor blocks. Adv. Sci. 9, 2202022 (2022).
Kataria, M. et al. Y-series-based polymer acceptors for high-performance all-polymer solar cells in binary and non-binary systems. ACS Energy Lett. 7, 3835–3854 (2022).
Liu, T. et al. 16% efficiency all-polymer organic solar cells enabled by a finely tuned morphology via the design of ternary blend. Joule 5, 914–930 (2021).
Hu, K. et al. Chlorinated polymerized small molecule acceptor enabling ternary all-polymer solar cells with over 16.6% efficiency. Sci. China Chem. 65, 954–963 (2022).
Ma, R. et al. Unveiling the morphological and physical mechanism of burn-in loss alleviation by ternary matrix towards stable and efficient all-polymer solar cells Adv. Mater. 2212275 https://doi.org/10.1002/adma.202212275 (2023).
Arunagiri, L. et al. Selective hole and electron transport in efficient quaternary blend organic solar cells. Joule 4, 1790–1805 (2020).
Chen, Y. et al. Asymmetric alkoxy and alkyl substitution on nonfullerene acceptors enabling high-performance organic solar cells. Adv. Energy Mater. 11, 2003141 (2021).
Yu, G. et al. Polymer photovoltaic cells: enhanced efficiencies via a network of internal donor-acceptor heterojunctions. Science 270, 1789 (1995).
Sun, Y. et al. Simultaneously enhanced efficiency and mechanical durability in ternary solar cells enabled by low-cost incompletely separated fullerenes. Macromol. Rapid Commun. 2200139 https://doi.org/10.1002/marc.202200139 (2022).
Li, Z. et al. Fine tuning miscibility of donor/acceptor through solid additives enables all-polymer solar cells with 15.6% efficiency. Sol. RRL 5, 2100549 (2021).
Li, N. et al. Abnormal strong burn-in degradation of highly efficient polymer solar cells caused by spinodal donor-acceptor demixing. Nat. Commun. 8, 14541 (2017).
Pont, S. et al. Stability of polymer:PCBM thin gilms under competitive illumination and thermal stress. Adv. Funct. Mater. 28, 1802520 (2018).
Distler, A. et al. The effect of PCBM dimerization on the performance of bulk heterojunction solar cells. Adv. Energy Mater. 4, 1300693 (2014).
Pont, S. et al. Dynamic PCBM: dimer population in solar cells under light and temperature fluctuations. Adv. Energy Mater. 9, 1803948 (2019).
Kim, H. K. et al. Linker unit modulation of polymer acceptors enables highly efficient air-processed all-polymer solar cells. Adv. Sci. 9, 2202223 (2022).
Ramanitra, H. H. et al. Increased thermal stabilization of polymer photovoltaic cells with oligomeric PCBM. J. Mater. Chem. C 4, 8121 (2016).
Raissi, M. et al. Main-chain poly(fullerene) multiblock copolymers as organic photovoltaic donor–acceptors and stabilizers. J. Mater. Chem. A 5, 7533–7544 (2017).
Wang, Y. et al. Boosting the fill factor through sequential deposition and homo hydrocarbon-solvent toward efficient and stable all-polymer solar cells. Adv. Energy Mater. 12, 2202729 (2022).
Cao, C. et al. Quasiplanar heterojunction all-polymer solar cells: a dual approach to stability. Adv. Funct. Mater. 32, 2201828 (2022).
Zhao, C. et al. An improved performance of all polymer solar cells enabled by sequential processing via non-halogenated solvents. Nano Energy 104, 107872 (2022).
Yu, H. et al. Effects of halogenation of small-molecule and polymeric acceptors for efficient organic solar cells. Adv. Funct. Mater. 2300712 https://doi.org/10.1002/adfm.202300712 (2023).
Chai, G. et al. Enhanced hindrance from phenyl outer side chains on nonfullerene acceptor enables unprecedented simultaneous enhancement in organic solar cell performances with 16.7% efficiency. Nano Energy 76, 105087 (2020).
Wood, S. et al. Assessing the validity of transient photovoltage measurements and analysis for organic solar cells. Phys. Rev. Appl. 10, 24038 (2018).
Shuttle, C. G. et al. Experimental determination of the rate law for charge carrier decay in a polythiophene: fullerene solar cell. Appl. Phys. Lett. 92, 93311 (2008).
Cheung, A. M. et al. Incorporation of alkylthio side chains on benzothiadiazole-based non-fullerene acceptors enables high-performance organic solar cells with over 16% efficiency. J. Mater. Chem. A 8, 23239–23247 (2020).
Yao, H. et al. All-polymer solar cells with over 12% efficiency and a small voltage loss enabled by a polymer acceptor based on an extended fused ring core. Adv. Energy Mater. 10, 2001408 (2020).
Hexemer, A. et al. A SAXS/WAXS/GISAXS beamline with multilayer monochromator. J. Phys. Conf. Ser. 247, 012007 (2010).
Mai, J. et al. Hidden structure ordering along backbone of fused-ring electron acceptors enhanced by ternary bulk heterojunction. Adv. Mater. 30, 1802888 (2018).
Dela Peña, T. A. et al. Understanding the charge transfer state and energy loss trade-offs in non-fullerene-based organic solar cells. ACS Energy Lett 6, 3408–3416 (2021).
Qian, D. et al. Design rules for minimizing voltage losses in high-efficiency organic solar cells. Nat. Mater. 17, 703–709 (2018).
Zhang, J. et al. Accurate determination of the minimum HOMO offset for efficient charge generation using organic semiconducting alloys. Adv. Energy Mater. 10, 1903298 (2020).
Karuthedath, S. et al. Impact of fullerene on the photophysics of ternary small molecule organic solar cells. Adv. Energy Mater. 9, 1901443 (2019).
Chen, D. et al. Printable and stable all-polymer solar cells based on non-conjugated polymer acceptors with excellent mechanical robustness. Sci. China Chem. 65, 182–189 (2021).
Acknowledgements
S.C. thanks to the support from the National Natural Science Foundation of China (No. 020513004026) and Fundamental Research Funds for the Central University (grant nos. 020514380274 and 020514380284). H. Yan appreciates the support from the National Key Research and Development Program of China (No. 2019YFA0705900) funded by MOST, the Basic and Applied Research Major Program of Guangdong Province (No. 2019B030302007), National Natural Science Foundation of China (NSFC, No. 22075057), the Shen Zhen Technology and Innovation Commission through (Shenzhen Fundamental Research Program, JCYJ20200109140801751), the Hong Kong Research Grants Council (research fellow scheme RFS2021-6S05, RIF project R6021-18, CRF project C6023-19G, GRF project 16310019, 16310020, 16309221, 16309822), Hong Kong Innovation and Technology Commission (ITC-CNERC14SC01) and Foshan-HKUST (Project No. FSUST19-CAT0202), Zhongshan Municipal Bureau of Science and Technology (No. ZSST20SC02) and Tencent Xplorer Prize.
Author information
Authors and Affiliations
Contributions
H. Yu, H. Yan, and S.C. conceived and designed the experiments. H. Yu and J.Y. synthesized PY-V-γ and PFBO-C12. Y.W. fabricated the devices and performed partial device characterizations supervised by Z.Z. X.S. and L.W. assisted with the material synthesis and characterizations. X.Z. did the photophysical measurements and analyzed the data supervised by K.S.W. Y.L. did the GISAXS measurements and analyzed the data supervised by X.L. H.Z. did the GIWAXS measurements and analyzed the data supervised by W.M. H.M.N. and B.Z. carried out the UV and CV measurements. H. Yu, Y.W., Z.Z., H. Yan, and S.C. took part in the discussions and gave important suggestions. H. Yu, Y.W., H. Yan, and S.C. co-wrote the manuscript.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Peer review
Peer review information
Nature Communications thanks Hyojung Cha, Roger Hiorns and the other, anonymous, reviewer(s) for their contribution to the peer review of this work.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Source data
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Yu, H., Wang, Y., Zou, X. et al. Improved photovoltaic performance and robustness of all-polymer solar cells enabled by a polyfullerene guest acceptor. Nat Commun 14, 2323 (2023). https://doi.org/10.1038/s41467-023-37738-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-023-37738-9
This article is cited by
-
An asymmetric non-fused electron-deficient building block for low-cost polymer acceptor in all-polymer solar cells
Science China Chemistry (2023)
-
Investigation of the electrical, optical and photophysical properties of PTB7:PCBM-thin films
Journal of Materials Science: Materials in Electronics (2023)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.